+7 (812) 645-08-06
Rolling bearing parts and accessories
select brand
Inner ring - ID : 6 - 220 mm, OD : 9 - 240 mm
Machined needle roller bearings inner rings are extremely strong as they are made from hardened rolling bearing steel. They are fitted with precision machined or ground raceways...
Inner ring - ID : 6 - 220 mm, OD : 9 - 240 mm
Machined needle roller bearings inner rings are extremely strong as they are made from hardened rolling bearing steel. They are fitted with precision machined or ground raceways and used in a variety of applications. They are mainly used in conjunction with cage assemblies and needle roller, drawn cup needle roller bearings with closed end and needle roller bearings, and also with drawn cup needle roller bearings with open ends when the shaft cannot be used as a raceway. The combination of needle roller bearings with wide inner rings can help in axial displacements of the shaft in conjunction with the housing. Finally, they are used when optimal running surfaces are required for seal lips.
Roller cage mixed-flow - ID : 8 - 90 mm, OD : 21 - 120 mm | AXK series
Axial cylindrical roller and cage assemblies consist of axial cages fitted one or two rows of cylindrical rollers. The distinctive features of the cage assemblies...
Roller cage mixed-flow - ID : 8 - 90 mm, OD : 21 - 120 mm | AXK series
Axial cylindrical roller and cage assemblies consist of axial cages fitted one or two rows of cylindrical rollers. The distinctive features of the cage assemblies are its small axial height, high radial load capacity and rigidity. They are able to support the axial force in one direction and quite capable of functioning as non-locating bearings in a radial direction. It is possible to combine the axial cage assemblies in the housing or shaft locating washers or they can be integrated directly in the adjacent construction. If there are no axial bearing washers, then the raceway will act as a rolling bearing raceway.
Hydraulic bearing puller - PULLER44 series
The PULLER-SUPPORT pressure tool in combination with mechanical extractors are used to...
Hydraulic bearing puller - PULLER44 series
The PULLER-SUPPORT pressure tool in combination with mechanical extractors are used to loosen tightly fitted parts. The tool is applied between the shaft end and extractor spindle. Care should be taken to ensure that the extractor's spindle diameter is not below the stated minimum value and the maximum torque must be observed.
Hydraulic bearing puller / three-arm - HYD series
The hydraulic extractors are designed for use in applications that require higher extraction forces. The devices allow quick and easy mounting of rolling bearings, gears, sleeves and many other shrink fitted parts. Longer extraction arms...
Hydraulic bearing puller / three-arm - HYD series
The hydraulic extractors are designed for use in applications that require higher extraction forces. The devices allow quick and easy mounting of rolling bearings, gears, sleeves and many other shrink fitted parts. Longer extraction arms are available (accessories) for larger grip depths. The operating personnel is protected by means of a safety grid or a safety cover.
The parts under mechanical load of the hydraulic extractors are made of high quality chromium-molybdenum steel. The smooth-running piston is composed of chromium plated, hardened and tempered steel. A standard adapter adjusts the stroke travel and the screw thread sets the optimum grip depth. Spring-loaded steel cone enables simple centering. Simple conversion to two-arm operation helps in cases of insufficient spaces for three arms. Rotatable pump hand lever or separate pump ensures an optimum operating position.
The parts under mechanical load of the hydraulic extractors are made of high quality chromium-molybdenum steel. The smooth-running piston is composed of chromium plated, hardened and tempered steel. A standard adapter adjusts the stroke travel and the screw thread sets the optimum grip depth. Spring-loaded steel cone enables simple centering. Simple conversion to two-arm operation helps in cases of insufficient spaces for three arms. Rotatable pump hand lever or separate pump ensures an optimum operating position.
Mechanical bearing puller
Timken's line of simple-to-use mechanical pullers provides the maintenance professionals with economical options. The mechanical pullers...
Mechanical bearing puller
Timken's line of simple-to-use mechanical pullers provides the maintenance professionals with economical options. The mechanical pullers includes a self-centering feature to ensure you with easier process. Based on the required pulling force, the right type of mechanical puller is to be chosen. Safety is the most important factor. Three-arm pullers are more capable to distribute the pulling force better than two-arm pullers, making three-arm pullers the foremost choice if there is enough room to use them.
Bearing isolator - -40 °C ... +204 °C
The bearing isolators from Timken extend the existence of electric motors by jamming pollutants. Decide between our normal lipless and step-pipe plans to fit your function...
Bearing isolator - -40 °C ... +204 °C
The bearing isolators from Timken extend the existence of electric motors by jamming pollutants. Decide between our normal lipless and step-pipe plans to fit your function and working atmosphere. Plan characteristics: Our non-metallic bearing separators are simple to set up, in the field or in the revamp shop. They offer bearings through an additional coating of safety from pollutants. They do not need lubrication throughout the process. They convene IEEE 841-2001 examination principles. They do not need setting up instruments. Uses include: The bearing isolators from Timken enhance the performance of electric motors in a wide variety of manufacturing applications
Hydraulic bearing puller / three-arm - 4 - 30 t
The self contained hydraulic pump and puller saves space ideal for removing all kinds of shaft-fitted parts. Timken created this tool to help in pulling...
Hydraulic bearing puller / three-arm - 4 - 30 t
The self contained hydraulic pump and puller saves space ideal for removing all kinds of shaft-fitted parts. Timken created this tool to help in pulling a wide variety of press fit parts including pulleys, gears, bushings, bearings, and wheels. It's for long time use through proper service, installation, and removal of the hydraulic pump and puller. The pump handle is flexible to rotate to 360-degrees to use the puller in the most convenient position and portable hydraulic pulling systems that have capacities from 4-30 tons. It's used with two or three legs and sets are supplied in handy carrying case.
Ball / silicon nitride / ceramic / for bearings
Genuine Cerbec silicon nitride balls are widely used in processing equipment to improve bearing performance. Cerbec balls...
Ball / silicon nitride / ceramic / for bearings
Genuine Cerbec silicon nitride balls are widely used in processing equipment to improve bearing performance. Cerbec balls are lighter, stiffer, smoother, harder, corrosion resistant, require less lubrication, and feature lower thermal expansion than their steel counterparts which increases the speed of bearings and increases operational temperatures with lower torque. The cerbec balls feature better oscillation, extreme temperature and are extremely durable.